Welcome to Our Community

Some features disabled for guests. Register Today.

Build List

OpenBuilds OX CNC Machine

Apr 23, 2021
Category
Cartesian Style CNC
Build Progress
Build Complete!

OpenBuilds OX CNC Machine. A strong easy to build shop CNC router that can be sized to suit your needs. Many new features have been incorporated into the OX to make it a great router that is sure to inspire!

WorkBee CNC Machine

Nov 20, 2023
Category
Cartesian Style CNC
Build Progress
Build Complete!

The WorkBee is our latest CNC Machine and is a culmination of all our experience, feedback, and suggestions from selling the OX CNC Machine over the past 2 years. The WorkBee is capable of accurately cutting foams, woods, plastics or aluminum at depths greater than 25mm to 0.2mm accuracy or greater.

OpenBuilds LEAD CNC Machine 1515 (60" x 60")

Sep 6, 2023
Category
CNC ROUTER
Build Progress
Build Complete!

It began with creating an extremely rigid axis that incorporates a multi C-Beam Linear Rail system as well as precision lead screws coupled with a tension system for the absolute maximum in performance.

GRANITE 1.0

Dec 25, 2018
Category
Cartesian Style CNC
Build Progress
Build in Progress...

This machine has been in the works for quite a while. Most of the plates were cut with my Shpinx machine. I have a lot more photos and information to share soon.

myOX : a 4' x 2' OX CNC with potential

Mar 14, 2016
Category
Cartesian Style CNC
Build Progress
Build Complete!

This is the story of me building myOX - my version of the "ideal" OX. I want a machine which can route/mill at least 4' wide and as long as I can feed through (don't be shy, think "infinity") as well as going deep on multiple faces - manual 4th axis. I have loads of ideas to take myOX towards that goal and way beyond. Time will tell. Just follow along through this build and possibly a few others along the way ... Check out my OXCalculator : let your computer figure out your BoM

Salmon Sphinx 1.0

Jul 22, 2017
Category
Cartesian Style CNC
Build Progress
Build in Progress...

A tribute build based on Kyo's wonderful CBeam Sphinx. My hope is to improve on that build slightly, but to be honest, I'll probably just screw it up. I'll use this build to publicly document my failures.

The Bull Dog, A RoverCNC OX based 1500mm x 1500mm CNC - Tutorial build

Jan 20, 2016
Category
Cartesian Style CNC
Build Progress
Build in Progress...

I have based this build on the OX build so I will not be going into too much detail of specefic assembly modules as they asre so well covered by Mark Carew already, but will go through the complete build on video. I will be addig additional tutorials on steppers and the other electronic parts as needed though as this project is sponsored by RS Components in the form of most of the Electronics and this is also the key focus of my YouTube channel www.youtube.com/c/thebreadboardca.

CNC Router Lathe

Feb 11, 2018
Category
Other Style CNC Mills
Build Progress
Build Complete!

Steel square tube frame with dual feed gantry and indexing lathe section. Will have 36" x 30" x 6" travel. Has a Harmonic Drive on the 4th Axis.

DIY CNC Machine

Jun 8, 2019
Category
CNC ROUTER BUILDS
Build Progress
Build Complete!

In this project, I show you how I built my DIY CNC machine. All moving parts of the DIY CNC router are running on ball bearings while the structural parts are made with natural materials, namely birch plywood and solid beech wood.

7050 Sphinx

May 25, 2018
Category
Cartesian Style CNC
Build Progress
Build Complete!

This is a Kyo Sphinx CNC Router build. Working Area: 350mm X 500mm Link to original design: https://openbuilds.com/builds/c-beam-sphinx.3605/

Workbee CNC Router/Laser/Plotter

Jan 31, 2022
Category
X/Y Table Style CNC Mill
Build Progress
Build Complete!

A CNC machine with an expansive 30x30" work area, supporing a router, laser, simple plotting and work monitoring camera. Control includes a tethered control box, game controller style jog control, and relay controlled AC outlets for all appliances. Accessories include a 3D printed dust shoe, a complete spoilboard and hold down system, an XYZ touch probe and multiple vacuum retention boards to support full profile routing.

PhlatPrinter MK 3

Jun 20, 2018
Category
Other Style CNC Mills
Build Progress
Build Complete!

The Phlatprinter 3 was designed to be used in a small shop with the ability to cut large sheets of foam for RC airplane projects. The idea was that you could save all of your aircraft as models and tweak to perfection after every flight.

Modular DIY CNC Machine

Jan 21, 2018
Category
Cartesian Style CNC
Build Progress
Build Complete!

This modular CNC machine is based on the OpenBuilds ACRO System, however I wanted something that did more than just laser engrave. So I designed my machine using the same style as the ACRO but with some upgrades such as an actual Z-axis and the ability for multiple tool attachments.

FRANKINATOR -- My CNC Router Built Around The C-Beam Rail

Feb 2, 2016
Category
Cartesian Style CNC
Build Progress
Build in Progress...

I started this build about 2 weeks after the c-beam hit the store. I purchased a single bundle and ordered a TinyG to run it. where I work I have Hardware, Software and Mechanical engineers and they all got sucked into my project. they want one to do prototyping at the office, once they see mine...

High Z Mod for Lead CNC

Oct 28, 2019
Category
CNC ROUTER
Build Progress
Build Complete!

The High Z modification for the LEAD CNC brings your creative capabilities to new heights! With 8" of clearance this modification can be adapted easily to your existing LEAD CNC Router.

Proteus

Nov 26, 2013
Category
X/Y Table Style Bots

Proteus is the Greek God of change. Besides the numerous aspect of 3D printing that this could relate to this machine like the god can change. The Build allows for an interchanging head that will allow different functionality to be quickly and easily adapted. So you could print clay, silicon, plastic, cut with a laser cutter or even attach a rotary tool

C-Beam Prefab Untitled

Sep 24, 2016
Category
Cartesian Style CNC
Build Progress
Build in Progress...

The C-Beam Prefab Untitled is designed as the cartesian compliment to the C-Beam XL. With the exception of requiring a couple more 1000mm C-Beams and lead screws, the build requires a minimum of additional parts. The primary intention of the build is to maximize the cutting envelope while still staying within the sweet spot for C-beam rigidity. This design can easily be modified and allows for further custom structural components to be cut with the initial build platform.

Rawcnc 1.5 Desktop Edition

Jul 11, 2018
Category
Cartesian Style CNC
Build Progress
Build in Progress...

This will showcase the build of my Rawcnc 1.5. A rigid cnc router from the Swedish company Rawcnc, featuring a rather cool linear motion system, rack & pinion and steel reinforced X-axis capable of milling aluminum.

1510 Workbee Modified

Jan 22, 2019
Category
Cartesian Style CNC
Build Progress
Build in Progress...

Some of the things that I have done to my 1510 Workbee Installed Linear rails and bearing blocks with drawings. Installed Ops console Made conversion plates for extruded aluminum to casters Extended z axis travel by a couple inches with steel plates. As of now in the process of installing Lead screws across the 1500mm length.

Sphinx 55

Feb 10, 2021
Category
Cartesian Style CNC
Build Progress
Build Complete!

A Sphinx build to inspire and encourage all those who want to get started with cnc to check out Opensbuilds line of machine bundles and hardware.

CNC FOR EVERYONE!

May 12, 2014
Category
Other Style CNC Mills
Build Progress
Build Complete!

This build was very complex due to the fact I wanted to create a low cost larger than normal CNC. I did not want a MDF or plastic body. I wanted it to be able to do more than most CNC routers this size on the market.

M4: 1510SS Heavy Mk.I

Aug 22, 2020
Category
Cartesian Style CNC
Build Progress
Build in Progress...

A 1500x1200mm, 20mm rail and 1610 ballscrew, heavy-duty, four-axis gantry machine. As high speed as spindle power MRR will allow for. Approx 4 x 3 x 1ft travels, intermediate size between benchtop and floor-scale units. Aiming at $10-15k machine in the $3k region.

Routy GT2 300 BSX CNC Router

Jun 24, 2015
Category
Cartesian Style CNC
Build Progress
Build Complete!

This is the first project that I would like to share with you. I know the build looks familiar and it is; it’s based on kram242´s Routy. Work area is 300*500*55 mm and is NEMA17/GT2 belt driven.

Aluminum OX build with some modifications

Mar 15, 2020
Category
Cartesian Style CNC
Build Progress
Build Complete!

This is my OX CNC router. It has been a labor of love for over a year now! I hope you find it interesting and inspiring! I also hope that it gives some of you more experienced CNC builders a different perspective and some ideas!

Fixed Gantry CNC Router with Old Industrial Supplies

Oct 8, 2019
Category
X/Y Table Style CNC Mill
Build Progress
Build Complete!

I got lucky enough to purchase aluminum extrusions and linear motion components (and nuts/bolts/etc) at scrap metal prices when a bunch of industrial automation equipment was decommissioned. The only problem is that the aluminum extrusions are not metric sizes... they are the 1.5"x3" 80/20 series. It has presented a few challenges but nothing too bad.

C-Beam Mini Mite

Jul 9, 2022
Category
X/Y Table Style CNC Mill
Build Progress
Build Complete!

A small system with a big bite. Design achieves a good balance between machine size vs. build area, rigidity and ease of construction all while keeping build cost as low as possible.

Vox Solid State

Mar 15, 2019
Category
Cartesian Style CNC
Build Progress
Build in Progress...

I never thought owning a CNC machine was possible until I stumbled upon the Openbuilds site. After viewing numerous builds I was drawn to the Ox by Mark Carew but ultimately decided on a build of similar design, Halloumi by Savvas. It's a C-beam design driven by Nema 23 steppers with Acme lead screws. Like Savvas I will be fabricating temporary plates to get up and running then use the machine to mill the final plates. The material I'm using for the temp plates is solid surface (Avonite).

DIY Slab Flattening Mill

Jul 8, 2020
Category
Everything Else
Build Progress
Build Complete!

V-SLOT profiles and OpenBuilds accessories give us many possibilities. We decided to build a manual ROUTER SLED using only components of the OpenBuilds system. The design is simple to build, construction takes little time, and the frame is easy to transport.

Build #2 - Bigger & Stronger

Jan 11, 2018
Category
X/Y Table Style CNC Mill
Build Progress
Build in Progress...

Large format CNC router with a 1500mm x 3000mm cutting envelope (5 x 10 ft) strong enough to cut wood and aluminum constructed from 20-series and 40-series aluminum extrusions. Complete Project Log w/ Pictures: https://goo.gl/photos/Co81AvGwVijE2zow9

Openbuilds C-beam

Nov 22, 2017
Category
CNC ROUTER BUILDS
Build Progress
Build Complete!

This is a build supported by Ooznest by a team of girls in Year 8 (12/13 years old) to machine model F1 cars for the F1 in Schools competition.

Angus : A Slightly "Beefier" OX

Dec 1, 2014
Category
CNC ROUTER BUILDS
Build Progress
Build in Progress...

This is where I will share my attempt at building a slightly "beefier" OpenBuilds OX CNC Machine using commonly available parts in the spirit of OPENBUILDS and Open Source in general. I have a tendancy to over-build things so I will be balancing that tendacy against budget constraints and common sense as much as possible.

Gantry Style CNC from plywood

Mar 4, 2021
Category
Cartesian Style CNC
Build Progress
Build in Progress...

I am currently 15 years old, from Germany and trying to build a low budged CNC router. I only designed this CNC based on other CNC routers that I have seen and what I am able of. It consists mostly of 2.3cm plywood to keep costs down. The size of the work area is approx. 40 x 80 cm. I would be really glad if you could give me advice's for improvement on the design and everything else ... ( I could really need your help :) ) enjoy :)

My Ox

May 16, 2015
Category
Cartesian Style CNC
Build Progress
Build Complete!

What I want to build is a unit to: rout wood, plastic and occasional aluminium . to be able to swap cutters. i.e. drragknife, laser, router, drill

My JGro CNC becomes an OpenBuild Project

Jan 3, 2015
Category
X/Y Table Style CNC Mill
Build Progress
Build in Progress...

This is the story of my progression from the JGRO cnc router design to using the OpenBuild system. In the process I think I have learned some things about cnc routers and the accuracy required to make a good build.

OPENBUILDS Korea (ROVO 1000)

Feb 7, 2015
Category
Cartesian Style CNC
Build Progress
Build in Progress...

I am very grateful to Mark Carew with passion and imagination. Therefore, the machine is good, but making the website there too daedanhaeseo The end of the same either way to invisible homework. Thank you for allowing openbuilds team submitted to the challenge once again for those with a passion that I feel like in Korea, I want to be a great help.

RSW's C-Beam Build

Feb 18, 2017
Category
X/Y Table Style CNC Mill
Build Progress
Build Complete!

I built a CNC Router using 3/4 MDF, 1/8 aluminum angle for bearing races and various other odds and ends. I learned a lot about how not to build a CNC router. I found Openbuilds.com and decided to build a C-Beam for my first build. The long term idea is to use this machine to build custom plates for and OX type machine and a 3d printer.

Matt's Ox

Aug 8, 2016
Category
Cartesian Style CNC
Build Progress
Build Complete!

I'm building an OX CNC router. It will be the larger size of 750x 1000mm. This should give me a working area of about 22"x30".

Router Sled V1.1 V-SLOT

Oct 26, 2020
Category
Everything Else
Build Progress
Build Complete!

We want to present you the new design of the device which is Router Sled. The whole structure is made of aluminum elements and ensures good quality of the device. We used V-SLOT aluminum profiles and OpenBuilds accessories for the construction. The instructional video can be found on our YouTube channel (subtitles in English soon)

Adjustable Router Guide Template

Feb 9, 2017
Category
Everything Else
Build Progress
Build Complete!

This project is an adjustable router guide template made with 20x60 V-slot. It was meant as a less expensive and more user friendly alternative to commercially available units.

OX CNC Router

Jul 20, 2017
Category
Cartesian Style CNC
Build Progress
Build Complete!

Ca fait 2 ans que je rêve d'une Fraiseuse CNC. Ni trop grande ni trop petite, sans avoir le budget pour en acheter une toute faite. Je suis artisan menuisier ébéniste et j'ai finalement décidé de la construire. Le projet OX m'a séduit, alors je me lance.

L'FOX - Large Format OX deriviative. Designed and built by Revision 13 Prototypes

Mar 9, 2017
Category
Laser Cutter Builds
Build Progress
Build in Progress...

This build is for a testing rig to use while testing out different controller boards and CAM software for milling and routing. It is in the early stages, planning is complete, parts are ordered. Awaiting parts delivery to start build. Please not the BOM only covers parts from the OpenBuilds part store. I will be posting the other required items very shortly.

C-beam Router rack and pinion

Sep 24, 2015
Category
Cartesian Style CNC
Build Progress
Build in Progress...

I want build a frame that is as sturdy as possibility while at the same time keeping it as compact as possible. working area will be approx 1200mm x 600mm

C-Beam Double X

Sep 11, 2015
Category
Cartesian Style CNC
Build Progress
Build in Progress...

Per the special notes its a variant of the C-Beam, Machine.... I have noticed that alot of people build a CNC router to cut parts for other larger CNC machines.. eg Delta Printers etc....plus this will enable me to cut parts for model RC plans UAV's etc...

The Growler

Feb 27, 2019
Category
Cartesian Style CNC
Build Progress
Build Complete!

This machine is a heavy duty, moving gantry style CNC router. It uses Teknic ClearPath servo motors driving ballscrews and linear rails. The machine has 36" x 48" x 19" of travel with about 7" of clearance below the gantry.

RiNo Route

Jan 5, 2017
Category
CNC ROUTER BUILDS
Build Progress
Build Complete!

A CNC router designed to handle a 4'x8' sheet, for as close to $2000 as possible. The price barrier resulted in my choice to use timing belts rather than leadscrews or rack&pinion. Build List still being updated

cnc plasma table

Apr 5, 2015
Category
OTHER BUILDS/PROJECTS
Build Progress
Build in Progress...

ive got most of the wire harness made up too im using Chinese electronics for now I will upgrade later when this thing makes me some cash lol im using a ibm think center to case to hold my electronics ive got a 25' parallel cable to put some distance between the table and the computer

Arctic Ox CNC Router

Jun 25, 2016
Category
Cartesian Style CNC
Build Progress
Build in Progress...

This is a cartesian CNC Router build that is based off the OX CNC build by Mark Carew. I am using Spark Concepts CNC xPro controller board and their 400w spindle kit.

Black Rabbit 1500

Sep 2, 2016
Category
Cartesian Style CNC
Build Progress
Build Complete!

This is a router that I designed that is loosely based on the Openbuilds Ox, but designed to be heavy duty, rigid, and yet quick and agile.

Loading...
Loading Build images...
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice