Select a Category
Build Author Robert E. Nee Views 971
Large cartesian gantry style 3D printer
This will be a fixed bed, v-slot implemented X,Y,Z axis gantry style 3D printer.
Build Author Savvas Views 2951
CNC Control Box with VFD etc etc
I'm currently working on the CNC control box, before doing any future work on the CNC Mountain Machine. I want the controller to be future proof and as professional as I can manage. I am planning to use stepper drivers, PSU's, a motor contactor unit to turn everything on, as well as a VFD and proximity limits switches. Each video will document the process and steps involved in researching, designing, planning and assembling a controller. I am not a natural electrician so learning as I go.
Build Author Lumberjack Engineering Views 3598
SOLAC: Space Optimized LAser Cutter
The Space Optimized LAser Cutter is a 40 watt CO2 laser cutter that supports a maximum part volume of 24" x 16" x 6.25". It consists of a V-slot frame + brackets/mounts designed to be 3D printed on a consumer desktop printer. Total cost of the machine is ~ $1,400 USD.
Build Author Martin.Barfoed Views 43494
Large format 1200X1500mm OX Build using Stainless Steel plates, dual belt configuration. Limit switches is a mix of micro switches and NPN Proximity switches. Electronics based on parallel break out board, Long Motor Stepper drivers (Chinese stuff) and motors controlled by Mach3. Spindel will be Kress 1050.
Build Author mikev Views 1222
C-Beam Evolution MkII
The C-Beam Evolution is an evolving machine. The MkII is inspired by Kyo's C-Beam Spinx but currently uses my own design of plates made of 8mm acrylic (X-axis ends) and 6mm polycarbonate (Y axis ends). The plates were made on the MkI but I hope to be able to make 6mm aluminium plates on the MkII for the MkIII. Currently I am in the process of fitting the limit switches and adding motor wiring and cable chains
Build Author Ken376 Views 683
Welded project cnc first try
Kind of hard to see in this pic now lining up drive s and finishing framework
Build Author Venturebit Views 969
SHRED-Buddy3D UPcycler - Open Source Multi Material Cutter&Pelletizer
The whole system is powered by 12V / DC power. Process it into Pellets or Granules to use it with your 3D Printer or Filament Extruder. Our self-developed steppermotor Controls allows you to optimally adjust Feedrate for your Situation. Forward, Backward and Stop is integrated for easy operation. The Speed can be continuously regulated via rotary switch.
Build Author Rwetzler Views 3443
This is a variant of a typical OX (Mark Carew inspiration) router using C-Beams/8mm Acme rods to drive all three axis. I went with a 1000mm x 1000mm frame size. Useable space is 28" (711mm) X 26" (660mm) with a Z axis work travel of approx. 3.25" (82.5mm). A TinyG is used as a controller along with Fusion 360/Chilipper as the software for generating and running gcode files.
Build Author Neptunes Guitars Views 3889
First build of CNC OX for the purpose of using it for Guitar building to take a lot of the muscle work out so I can concentrate on the finer details.
Build Author Gerrald Views 1838
This build is to show what's possible as well with openBuilds! I use a single ArduinoMega and 5 separate stepper drivers (A4988). The LEDs are all NeoPixels. Collision 'detection' is all done within the code, so the endstops are only sensors I use in this build. I'm a self-employed video-artist and this is my first installation which just needs power and it runs (where I'm quite proud of). Normally my interactive installations take a long setup time, so this installation is a relief :)
Build Author Mogens Kusk Views 2588
Belt driven 1200mm x 700mm x170mm axis