Welcome to Our Community

Some features disabled for guests. Register Today.

OX Cable Management, Electronics Case, E-Stops

Discussion in 'CNC Mills/Routers' started by andrew Adsit, Feb 20, 2015.

  1. andrew Adsit

    Builder

    Joined:
    Jan 27, 2015
    Messages:
    27
    Likes Received:
    20
    andrew Adsit published a new build:

    Read more about this build...
     
    GrayUK likes this.
  2. sgspenceley

    sgspenceley Veteran
    Builder

    Joined:
    May 27, 2014
    Messages:
    249
    Likes Received:
    291
    Andrew very nice ideas and installation on cable management!
    What type of connectors are you using? Do you have a supplier link?
     
  3. andrew Adsit

    Builder

    Joined:
    Jan 27, 2015
    Messages:
    27
    Likes Received:
    20
    I added a link to my list on Amazon with a lot of the parts I used, including the connectors. Some items out of stock, so you may have to shop around on Amazon.
     
    #3 andrew Adsit, Feb 20, 2015
    Last edited: Feb 20, 2015
  4. sgspenceley

    sgspenceley Veteran
    Builder

    Joined:
    May 27, 2014
    Messages:
    249
    Likes Received:
    291
    Thank you Andrew...
     
  5. Nick W

    Nick W Well-Known
    Builder

    Joined:
    Oct 22, 2014
    Messages:
    99
    Likes Received:
    61
    Thanks for the info. I just placed an order for those connectors. I have been thinking of how I was going to the wiring.
     
  6. ChadRat6458

    Builder

    Joined:
    Dec 10, 2014
    Messages:
    93
    Likes Received:
    24
    Looks real good. I am about to make a box for my controller and switches. I was thinking about mounting the power supply in the same box. Where are you mounting yours? Thanks.
     
  7. Nick W

    Nick W Well-Known
    Builder

    Joined:
    Oct 22, 2014
    Messages:
    99
    Likes Received:
    61
    I'm at the same point in my design. I have a few enclosure that can hold all the electronics except the power supplies. I would like to have them all in the same box for simplicity. My current thought is to make something temporary so I can run the OX so it can make a more permanent solution.
     
  8. andrew Adsit

    Builder

    Joined:
    Jan 27, 2015
    Messages:
    27
    Likes Received:
    20
    I built a shelf under the table for the power supplies (I use one for the OX and one just for the spinde. I am currently building my button box which will integrate the pi and a 3.5 touch display, the emergency off button and the run/resume and the pause button. Pictures tonight.

    I didn't want the power supplies in the boxes for 1) modularity and 2) heat.
     
  9. spark2

    spark2 New
    Builder

    Joined:
    Apr 9, 2014
    Messages:
    7
    Likes Received:
    6
    Hi Andrew. Really Nice Wire Management. I got a Question. How did you connect the Aluminium-Block of the Spindle with the Z-Axis? That would be interesting for my CNC Build. Thanks for your Help.
     
  10. andrew Adsit

    Builder

    Joined:
    Jan 27, 2015
    Messages:
    27
    Likes Received:
    20
    I used a short piece of 20x60 turned 90 degrees. I had to bevel the cut to avoid the wheel nuts, but the al block holes were a perfect match. Them I used 4 pieces of 5mm all thread cut to length with t-nuts in the 20x60 and regular nuts on the top. I'll post a pic in a few.
     
  11. spark2

    spark2 New
    Builder

    Joined:
    Apr 9, 2014
    Messages:
    7
    Likes Received:
    6
    thanks for your Answer. It would be great to see a Pic with your Solution, so i can imagine better. Thanks for your Help.
     
  12. andrew Adsit

    Builder

    Joined:
    Jan 27, 2015
    Messages:
    27
    Likes Received:
    20
    IMG_0294.JPG
     

    Attached Files:

    Nick W likes this.
  13. spark2

    spark2 New
    Builder

    Joined:
    Apr 9, 2014
    Messages:
    7
    Likes Received:
    6
    thanks for your effort. good idea how u fixed it.
     
  14. CASTELLINI

    Builder

    Joined:
    Nov 23, 2015
    Messages:
    5
    Likes Received:
    0
    Hello Andrew,

    Could you tell me what's your max Z axis travel please ?

    Thanks
    Adrien
     
  15. azarock

    azarock New
    Builder

    Joined:
    Oct 11, 2015
    Messages:
    21
    Likes Received:
    5
    Looks like a great build. :thumbsup:
     
  16. andrew Adsit

    Builder

    Joined:
    Jan 27, 2015
    Messages:
    27
    Likes Received:
    20
    With a 1" bit, almost 50mm with my standard waste board. If I remove it and use the board below it, I get another 60mm. So far, it has been enough, but if I wanted to do any relief carving, I would probably have to raise the y rails.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice