Welcome to Our Community

Some features disabled for guests. Register Today.

Cutting V-Slot

Discussion in 'General Talk' started by DarkAlchemist, Aug 24, 2014.

  1. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    What tool am I going to have to purchase that I can cleanly cut the extruded aluminum to build my router?

    I get a bit discouraged looking around the net when up keeps popping 200+ dollar chop saws and 500 dollar miter saws requiring an additional 60 dollar blade. At that rate I might as well buy a Chinese machine and work with it which I really do not want to do.

    My last hold off to starting the project is this part of the equation then I am going to intermix Routy and Ox.
     
  2. Brian Slee

    Brian Slee Well-Known
    Builder

    Joined:
    Apr 26, 2014
    Messages:
    191
    Likes Received:
    59
    If you don't mind a little work you could always use a $5 mitre box and a hacksaw
    [​IMG]
     
  3. dddman

    dddman Journeyman
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    468
    Likes Received:
    187
  4. Rick 2.0

    Rick 2.0 OpenBuilds Team
    Staff Member Moderator Builder Resident Builder

    Joined:
    Dec 20, 2013
    Messages:
    2,854
    Likes Received:
    1,525
    You could always check locally for rental equipment or check to see if you have a local hackerspace where you could cut it. Ultimately however, Brian's suggestion may be the best low cost option.
     
  5. Franco Ponticelli

    Builder

    Joined:
    Dec 4, 2013
    Messages:
    65
    Likes Received:
    14
    I cut mine by hand and with no miter box. Time consuming but not as half-bad as I initially envisioned. The miter box is certainly a great idea. I also planned my machine so that I would need the minimal number of cuts (using the one meter extrusions as side). Only a word of caution, the extrusions might have some tolerance and might not all be of the same length.
     
    #5 Franco Ponticelli, Aug 24, 2014
    Last edited: Aug 24, 2014
  6. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    Yes, I was thinking about the miter box and a 32T blade for the hack saw. I know I need that box as I have never been able to cut straight with a hacksaw.

    I forgot to add this question but will the 20x80 fit so it is laying down horizontally to cut?
     
    #6 DarkAlchemist, Aug 24, 2014
    Last edited: Aug 24, 2014
  7. Brian Slee

    Brian Slee Well-Known
    Builder

    Joined:
    Apr 26, 2014
    Messages:
    191
    Likes Received:
    59
    If you get a box that can handle a standard 2x4 you shouldn't have any problem with the 80mm which is just a smidge over 3 1/8"
     
  8. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    Aye, with modern 2x4 boards being 2.5 x 3.5. Perfect, as I have never ever been able to make a straight cut with a hacksaw without guides.

    By the way do they make a better blade for this than the 32T for a hacksaw? Which brand is good in people's opinion as I use Lenox but getting a 32T Lenox has to be mail ordered here so if I am going to have to MO it I might as well ask if there is better and/or with more teeth and where from too.
     
  9. andrew

    andrew New
    Builder

    Joined:
    Mar 16, 2014
    Messages:
    47
    Likes Received:
    18
    Don't forget the cutting/tapping fluid. A couple drops in the cut lets the blade slide real smooth without binding.
    I've cut plenty of v-slot with the hacksaw. Works fine. I square it up on a belt sander afterwords for clean ends and perfect length.
     
  10. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    Which type and where to buy? :)
     
  11. Dave Millard

    Builder

    Joined:
    May 26, 2014
    Messages:
    27
    Likes Received:
    0
    WD40 working well for tapping, and also cutting on my saw.
     
  12. dddman

    dddman Journeyman
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    468
    Likes Received:
    187
    Depending on where you will buy your v-slot, they can cut it for you if you want
     
  13. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    I was going to buy all of my materials from the Open builds website as I am building a Routy but with the stability of the OX on the frame.

    Is there another source for V-Rail/V-Slot?
     
  14. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    Perfect, I was hoping that would work. Just use the pull stroke, not the push stroke, to cut it and spray it once before and once in the middle of each cut.
     
  15. dddman

    dddman Journeyman
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    468
    Likes Received:
    187
  16. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    I live in the USA so was going to go directly with the source but if the prices are lower and/or they will cut them for me and OB wouldn't I will go with someone else.

    Any preferences or just grab one?
     
  17. dddman

    dddman Journeyman
    Builder

    Joined:
    Mar 2, 2014
    Messages:
    468
    Likes Received:
    187
    I'm a distributor so... :p But I'm located in Quebec, there are distributors near you I'm pretty sure :)
     
  18. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    Ahhh, hehe
     
  19. andrew

    andrew New
    Builder

    Joined:
    Mar 16, 2014
    Messages:
    47
    Likes Received:
    18
    I use "Oatey Clear Thread Cutting Oil" from the local hardware store.
     
  20. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    I saw that at HD and was put off by the thread cutting part. Works really well I take? Any better than WD40?
     
  21. bobt

    bobt Well-Known
    Builder

    Joined:
    Dec 4, 2013
    Messages:
    89
    Likes Received:
    38
    Yes much better because most people do not know the "WD" stands for water dispersant. It is not a good lubricant. The last part of the part description is "Cutting Oil" and that is what you are doing. The "Thread" part of the name is just it's common usage.

    Bob
     
  22. DarkAlchemist

    DarkAlchemist Well-Known
    Builder

    Joined:
    Aug 2, 2014
    Messages:
    401
    Likes Received:
    22
    Yep, I personally hate WD as I found much better for many jobs so I never understood why I see people (in videos) spray WD40 on the material as the spindle is cutting.
     
  23. raykholo

    raykholo New
    Builder

    Joined:
    Jun 29, 2014
    Messages:
    38
    Likes Received:
    4
    $120 Ryobi Miter Saw from home depot and $50 Oshlun blade: 10 inch for non ferrous metals with 100 carbide teeth. Cuts like butter. I make all my cuts dry.
     
  24. oldfox

    oldfox New
    Builder

    Joined:
    Aug 12, 2014
    Messages:
    3
    Likes Received:
    0
    "Just use the pull stroke, not the push stroke"

    Wrong. Never try to cut with the teeth "scraping" on their backside. Always let the saw cut. Don't force it. If you are using any kind of handsaw, then I don't believe that you would need any lubricant of any kind.
    If you are more comfortable "pulling" a saw rather than "pushing" it, then turn the hacksaw blade around backwards. Done deal. (fwiw - Japanese woodworking saws are designed to be used on the pull stroke.)
    I cut extrusions, dry, with a DeWalt miter saw with a general purpose carbide blade. No problems other than the small little bits of aluminum sawdust (flakes) flying around. (glasses and earplugs please)
    If you are budget challenged, (is that politically correct?) then the miter box and hacksaw is at the bottom of the foodchain. If you ever decide to go powered, don't forget about a bandsaw. Small used ones can be had for not so much. Just don't get a 3-wheel. They're a real bear to get and keep the blade tracking. Stick to the 2-wheel variety.

    Well, that's my 2 cents worth. Back to work.
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice