Welcome to Our Community

Some features disabled for guests. Register Today.

Sign Up

Recent Content by Stanley Kitowski

  1. Stanley Kitowski
    Post

    Problem Engraving the Letter O or circles

    I tightened each v wheel hand tight. Then turned the eccentric spacer until the wheel couldn't move. I didn't know I needed to make them loose to...
    Post by: Stanley Kitowski, Oct 16, 2016 in forum: CNC Mills/Routers
  2. Stanley Kitowski
    Post

    Problem Engraving the Letter O or circles

    Hey Jimmy! This is a repeat message on the other thread, but I wanted to post here for others in case they are facing the same problem. Looks...
    Post by: Stanley Kitowski, Oct 15, 2016 in forum: CNC Mills/Routers
  3. Stanley Kitowski
    Post

    accuracy issue ooznest ox (what am i doing wrong)

    Hey Jimmy! Looks like I found out what's causing the misalignment! Not the software, not the steppers, not the direction of cut, not the...
    Post by: Stanley Kitowski, Oct 15, 2016 in forum: CNC Mills/Routers
  4. Stanley Kitowski
    Post

    accuracy issue ooznest ox (what am i doing wrong)

    GRBL for both the old and updated CNC frame. I did use the old DRV8825 for the old CNC. This setup made perfect circles. The updated CNC used GRBl...
    Post by: Stanley Kitowski, Oct 15, 2016 in forum: CNC Mills/Routers
  5. Stanley Kitowski
    Post

    accuracy issue ooznest ox (what am i doing wrong)

    Thanks for the reply Jimmy! When I cut a circle and then cut another circle in the exact same position, it will not deviate, not even a tiny...
    Post by: Stanley Kitowski, Oct 15, 2016 in forum: CNC Mills/Routers
  6. Stanley Kitowski
    Post

    accuracy issue ooznest ox (what am i doing wrong)

    I am starting to think that the 20x80 t slot rails are racking. Is there a way to prove this? Maybe marking a spot shared by both rails and...
    Post by: Stanley Kitowski, Oct 14, 2016 in forum: CNC Mills/Routers
  7. Stanley Kitowski
    Post

    accuracy issue ooznest ox (what am i doing wrong)

    All tb6600 drivers have the same amperage 4.0a and steps 1/16
    Post by: Stanley Kitowski, Oct 14, 2016 in forum: CNC Mills/Routers
  8. Stanley Kitowski
    Post

    accuracy issue ooznest ox (what am i doing wrong)

    Hi Jimmy! I put my ox hybrid together and noticed that circles do not align over single passes (like engraving). I took my machine completely...
    Post by: Stanley Kitowski, Oct 14, 2016 in forum: CNC Mills/Routers
  9. Stanley Kitowski
    Profile Post Comment

    Kinda in the same boat! I've built a machine similar to the Ooznest that has the same exact...

    Kinda in the same boat! I've built a machine similar to the Ooznest that has the same exact problems! Circles do not line up and problem is...
    Profile Post Comment by Stanley Kitowski, Oct 14, 2016
  10. Stanley Kitowski
    Post

    Problem Engraving the Letter O or circles

    Doing some research and found another builder suffering from the same issues I seem to be having trouble with: accuracy issue ooznest ox (what am...
    Post by: Stanley Kitowski, Oct 14, 2016 in forum: CNC Mills/Routers
  11. Stanley Kitowski
    Post

    accuracy issue ooznest ox (what am i doing wrong)

    Hello Tore! I seem to be having the same issue as you! Problem Engraving the Letter O or circles Were you able to resolve your problem? Please...
    Post by: Stanley Kitowski, Oct 14, 2016 in forum: CNC Mills/Routers
  12. Stanley Kitowski
    Post

    Problem Engraving the Letter O or circles

    Great suggestion! Before I posted this problem on the forum, I swapped out each motor to find out if the problem would follow. No change in the...
    Post by: Stanley Kitowski, Oct 14, 2016 in forum: CNC Mills/Routers
  13. Stanley Kitowski
    Post

    Problem Engraving the Letter O or circles

    Alright folks, I did a whole lot of testing the past two days. I will upload some pictures of the results when I get back home. But based from...
    Post by: Stanley Kitowski, Oct 13, 2016 in forum: CNC Mills/Routers
  14. Stanley Kitowski
    Post

    Problem Engraving the Letter O or circles

    Agreed! Again, the Fusion 360 forum and you guys suggested the same thing! I am planning to do a set of circles with a single pass engrave and...
    Post by: Stanley Kitowski, Oct 11, 2016 in forum: CNC Mills/Routers
  15. Stanley Kitowski
    Post

    Problem Engraving the Letter O or circles

    Hey folks! Tried it again with a post processor (based on Openbuilds actually) for Fusion360. Here is the link for a paper trail: GitHub -...
    Post by: Stanley Kitowski, Oct 11, 2016 in forum: CNC Mills/Routers
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice